Kamil Perry
If your Good Cook cheese slicer is not working, the wire may be misaligned or broken. To fix a misaligned wire, place the slicer on a flat surface with the handle facing you, then gently rock the handle back and forth while pulling it slightly out of the board. If the wire is broken, you can replace it with a new one of the appropriate length. Simply remove the old wire by loosening the screw at the end of one of the arms and prying out the end of the wire, then repeat on the opposite arm. Next, loop the ends of the new wire into the slots on the arms and tighten the screws.
Explore related products
What You'll Learn
How to replace the wire on a Good Cook cheese slicer
To replace the wire on a Good Cook cheese slicer, follow these steps:
First, measure the distance between the arms of the cheese slicer to determine the correct length for the replacement wire. You can purchase replacement wires online or at stores that sell cooking utensils. If you cannot find a suitable replacement wire, you can use a guitar string or a high E string from a guitar, as suggested by Alton Brown and some Reddit users.
Once you have the replacement wire, place the cheese slicer on a flat surface with the handle end facing you. Loosen the handle by turning it upward and lift it so that it is perpendicular to the board. With gentle finger pressure, gently rock the handle back and forth while slightly pulling it out of the board. This will help align the wire with the groove if it is too far to the left.
Now, you can remove the old wire. Loosen and remove the screw at the end of one of the arms holding the wire in place. Use a nail to pry out the end of the old wire from that arm. Repeat this process on the opposite arm to completely remove the old wire.
Finally, install the new wire. Loop the ends of the new wire into the slots on the arms of the cheese slicer. Replace and tighten the holding screws to secure the new wire in place.
Your Good Cook cheese slicer is now ready to use again with a fresh wire!
Feta Cheese: The Perfect Alfredo Topping?
You may want to see also
Fixing a Good Cook cheese slicer with a guitar string
Cheese slicers have a simple construction, consisting of a wire held between the arms of a Y-shaped handle. Over time, this wire can wear out or break, requiring a replacement. If you cannot find a replacement wire, chef Alton Brown recommends using a guitar string.
To fix a Good Cook cheese slicer with a guitar string, first, measure the distance between the arms of the cheese slicer. This will help you know how long the guitar string needs to be. Then, cut the guitar string to the appropriate length. Loosen and remove the screw at the end of one of the arms holding the wire in place. You can use a nail to pry out the old wire from that arm. Repeat this process on the opposite arm to completely remove the old wire.
Now, take the guitar string and loop its ends into the slots for the wire on the arms of the cheese slicer. Make sure the string is taut and secure. Finally, replace and tighten the holding screws. Your Good Cook cheese slicer should now be ready to use again!
It is important to note that when choosing a guitar string, it is recommended to opt for a thinner string. Thinner guitar strings are more suitable for cutting cheese and are known to last longer.
Feta Cheese: Friend or Foe for Lactose Intolerance?
You may want to see also
Aligning the wire in the cutting slot of a Good Cook cheese slicer
The Good Cook cheese slicer, like most cheese slicers, has a simple construction consisting of a wire held taut between the arms of a Y-shaped handle. Over time, the wire can wear or break and will need to be replaced. When this happens, you can follow these steps to align the wire in the cutting slot:
First, place the board on a flat surface with the handle end facing you. Next, lift the handle so that it is perpendicular to the board. With gentle finger pressure, rock the handle back and forth gently while slightly pulling the handle out of the board, just enough so that the wire aligns with the groove. You can verify if the wire is properly aligned by rotating the arm down to the cutting position. If it is not, simply repeat the steps above.
If you need to replace the wire, first measure the distance between the arms of the cheese slicer to know the size of the replacement wire to buy. Replacement cheese wire is sold wherever cooking utensils are sold. If you cannot find cheese wire, you can use a guitar string instead. Once you have the replacement wire, follow these steps:
- Loosen and remove the screw at the end of one of the arms holding the wire in place in the slot at the end of the arm.
- Pry out the end of the old wire from that arm with the tip of a nail.
- Repeat the process on the opposite arm to completely remove the old wire.
- Loop the ends of the new wire into the slots for the wire on the arms.
- Replace and tighten the holding screws.
Goat Cheese: A Healthy Protein Source?
You may want to see also
Explore related products
Replacing a broken Good Cook cheese slicer wire
A broken Good Cook cheese slicer wire can be replaced by following these steps:
First, measure the distance between the arms of the cheese slicer to determine the correct size of the replacement wire. Replacement wires are available at most stores that sell cooking utensils, or you can use a high E guitar string as an alternative. If you own a Prodyne cheese slicer, you can take advantage of their lifetime replacement guarantee by sending a self-addressed, stamped envelope along with the broken wire to their customer service department.
Once you have obtained a replacement wire, place your cheese slicer on a flat surface with the handle facing you. Loosen the handle by unscrewing it and turn it upward. This will expose the wire and the mechanism holding it in place. Gently remove the old wire by loosening the screw at the end of one of the arms and use a nail to pry out the end of the wire from the slot. Repeat this process on the opposite arm to completely remove the old wire.
Now, take your new wire and loop the ends into the slots on the arms of the cheese slicer. Ensure that the wire is securely fitted and taut by tightening the holding screws. With your new wire in place, your Good Cook cheese slicer is ready to use again!
If you encounter any issues with aligning the wire in the cutting slot, you can make adjustments by gently rocking the handle back and forth while slightly pulling it out of the board. This will ensure the wire is correctly positioned and ready for use.
Dubliner Cheese: A Delicious Irish Treat?
You may want to see also
Fixing a Good Cook cheese slicer with a piece of wire
A cheese slicer has a simple construction, consisting of a wire held between the arms of a Y-shaped handle. Over time, this wire can wear or break and will need to be replaced.
To fix a Good Cook cheese slicer with a piece of wire, you will first need to measure the distance between the arms of the cheese slicer to know the size of the replacement wire to buy. Replacement cheese wire can be purchased wherever cooking utensils are sold, or you can use a guitar string as recommended by Alton Brown.
Once you have your replacement wire, follow these steps:
- Place the cheese slicer on a flat surface with the handle end facing you.
- Loosen the handle and turn it upward.
- Remove the screw at the end of one of the arms holding the wire in place. You can use a nail or a narrow object to pry out the end of the old wire from that arm.
- Repeat the process on the opposite arm to completely remove the old wire.
- Insert one end of the new wire through the hole in the wire tensioning nut.
- Use needle-nose pliers to create a 1/8-inch loop at the end of the wire.
- Tighten the wire tensioning nut and pull the wire loop flush against it.
- If your cheese slicer has rivets, direct the wire around them before reaching the second wire tensioning nut. If there are no rivets, pull the available end of the wire toward the other wire tensioning nut.
- Insert the other end of the wire through the opposite wire tensioning nut and create another 1/8-inch loop with the needle-nose pliers.
- Pull the loop flush against the wire tensioning nut and rotate the nut three revolutions to tighten the wire. Ensure that the wire is spooled evenly and does not interlace with itself or the wire loop.
Your Good Cook cheese slicer should now be fixed and ready for use!
Cheese Storage: Warm Temperature Effects Explained
You may want to see also
Frequently asked questions
To fix the wire on your Good Cook cheese slicer, first, place the board on a flat surface. Then, loosen and remove the screw at the end of one of the arms holding the wire in place. Pry out the end of the old wire from that arm and repeat the process on the opposite arm to completely remove the old wire. Measure the distance between the arms of the cheese slicer to know the size of the replacement wire to buy. Finally, loop the ends of the new wire into the slots for the wire on the arms and replace and tighten the holding screws.
Place the board on a flat surface with the handle end facing you. Lift the handle so that it is perpendicular to the board. With gentle finger pressure, rock the handle back and forth gently while slightly pulling the handle out of the board, just enough so that the wire aligns with the groove.
Replacement wires can be purchased from most places that sell cooking utensils. Alternatively, you can order a replacement wire directly from the Good Cook website.
