Randy Chandler
If the wire on your cheese slicer is broken, you can replace it with a new one. Before you start the replacement process, make sure to order the correct replacement wires for your cheese slicer. To replace the wire, first, unscrew the handle and remove the nut from the arm. Then, loop one end of the new wire into the groove at the base of the arm, and the other end of the wire onto the threads of the handle. Screw the handle back onto the retaining nut, slide the nut onto the arm, and tighten the wire by adjusting the angle of the handle. Finally, place the board on a flat surface, lift the handle, and gently rock it back and forth while slightly pulling it out of the board so that the wire aligns with the groove. Your cheese slicer is now ready to be used again!
| Characteristics | Values |
|---|---|
| Step 1 | Unscrew the handle from the retaining nut and remove the nut from the arm |
| Step 2 | Loop one end of the wire into the groove at the base of the arm and the other end of the wire onto the threads of the handle |
| Step 3 | Screw the handle back onto the retaining nut |
| Step 4 | Slide the retaining nut onto the arm, aligning the wire in the groove |
| Step 5 | Tighten the wire by adjusting the angle of the handle |
| Step 6 | When taut, screw the handle until it locks against the arm |
| Note | If the handle is adjusted too tightly, the cheese wire may break |
Explore related products
What You'll Learn
Unscrew the handle and remove the nut from the arm
To replace the wire on a cheese slicer, you'll first need to remove the handle. Start by unscrewing the handle from the retaining nut. Usually, this involves simply turning the handle until it comes loose. In some cases, you may need to first loosen the handle by rocking it back and forth gently while slightly pulling it out of the board. Once the handle is loose, you can unscrew it the rest of the way and remove the retaining nut from the arm of the cheese slicer.
The handle is attached to the arm of the cheese slicer via a retaining nut. This nut needs to be unscrewed from the arm to detach the handle completely. Make sure you keep track of the order in which the parts are assembled so that you can put them back together correctly later. Once the nut is removed, you can set the handle and nut assembly aside and move on to the next step of replacing the wire.
It's important to be careful when removing the handle and nut assembly. Cheese slicer wires are under tension, so there is a risk of injury if the handle is removed abruptly. Take your time and make sure the wire is not loose before proceeding. Once the handle and nut are removed, you can begin the process of installing the new wire. This typically involves looping the ends of the new wire into the appropriate grooves and then reassembling the handle and nut onto the arm.
If you're unsure about the disassembly process, it's always a good idea to refer to the manufacturer's instructions or seek guidance from a qualified technician. Remember to prioritize your safety and only proceed with the wire replacement if you feel comfortable with the procedure.
Cheese on Enchiladas: To Top or Not?
You may want to see also
Loop wire into the groove at the base of the arm
To loop wire into the groove at the base of the arm of your cheese slicer, start by unscrewing the handle from the retaining nut and removing the nut from the arm. Then, take the new wire and loop one end of it into the groove at the base of the arm. The wire should fit snugly into the groove. Next, slide the retaining nut back onto the arm, making sure that the wire remains in the groove. This will secure the wire in place.
It is important to ensure that the wire is properly aligned with the cutting slot. To do this, gently work the bar into or out of the base until the wire sits in the correct position. You may need to use gentle finger pressure to rock the handle back and forth while slightly pulling the handle out of the board to achieve the correct alignment. Once the wire is in place, tighten the wire by adjusting the angle of the handle. Be careful not to overtighten, as this may cause the wire to break.
Chicken Enchiladas: To Cheese or Not to Cheese?
You may want to see also
Slide the bar back into the base through the wire loop
To put a new wire on a cheese slicer, you will need to slide the bar back into the base through the wire loop. This process requires careful manoeuvring to ensure the wire is correctly positioned and taut.
Firstly, place the cheese slicer on a flat surface with the handle end facing you. Loosen the handle and turn it upward, perpendicular to the board. With gentle finger pressure, rock the handle back and forth while slightly pulling it out of the board. This step ensures the wire aligns with the groove.
Now, take the new wire and place the wire loop into the cutting slot. With the handle in the raised position, slide the bar back into the base, passing it through the wire loop. Ensure the wire is taut and secure by gently pulling on it.
The next step is to place the other wire loop into the handle cavity. Reinsert the fastening pin by passing it through the loop, then turn the handle until it comes to rest. Grasp the handle and tighten the set screw into the metal bar.
Finally, gently work the bar into or out of the base until the wire is perfectly aligned with the cutting slot. Your cheese slicer is now ready to use.
Mac and Cheese: Creative Add-Ins for a Classic
You may want to see also
Explore related products
Place the other wire loop into the handle cavity
Now that you have placed one wire loop into the cutting slot and slid the bar back into the base, it is time to place the other wire loop into the handle cavity. This step is crucial in securing the wire in place and ensuring the cheese slicer functions properly.
First, ensure that the handle is in the raised position. This will provide you with the necessary access to the handle cavity. The handle should be perpendicular to the board, creating a 90-degree angle.
With the handle raised, take the other end of the wire and carefully feed the wire loop into the handle cavity. This may require some gentle wiggling and maneuvering to ensure it is securely seated within the cavity.
Once the wire loop is in place within the handle cavity, you can proceed to the next step of reinserting the fastening pin. This pin will provide additional security, ensuring the wire remains firmly attached to the handle.
It is important to follow these steps carefully to guarantee the wire is securely attached and reduce the risk of any accidents or injuries when using the cheese slicer.
Cheese Frittata: Should You Add Cheese to Your Frittata?
You may want to see also
Tighten the wire by adjusting the handle angle
To tighten the wire on a cheese slicer, you will need to adjust the handle angle. This process will ensure the wire is taut and secure, allowing you to slice cheese effectively.
Firstly, you must ensure the wire is correctly installed. Loop one end of the wire into the groove at the base of the arm, and the other end should be looped onto the threads of the handle. Once this is done, screw the handle back onto the retaining nut.
Next, slide the retaining nut onto the arm, aligning the wire in the groove. This step is crucial as it ensures the wire is in the correct position.
Now, you can tighten the wire by adjusting the angle of the handle. This action will create tension in the wire. Adjust the handle until the wire is taut, and then screw the handle until it locks against the arm.
It is important to note that over-tightening can cause the wire to break, so be cautious not to adjust the handle too tightly. With the correct tension, your cheese slicer will be ready for use, and you can enjoy perfectly sliced cheese.
Cheese and Potato Salad: A Delicious Combination?
You may want to see also
Frequently asked questions
First, unscrew the handle and remove the nut from the arm. Then, loop one end of the wire into the groove at the base of the arm and the other end of the wire onto the threads of the handle. Screw the handle back on and slide the retaining nut onto the arm, aligning the wire with the groove. Tighten the wire by adjusting the angle of the handle and screw the handle until it locks against the arm.
Place the cheese slicer on a flat surface with the handle facing you. Lift the handle so that it is perpendicular to the board and rock the handle back and forth gently while slightly pulling the handle out of the board, until the wire aligns with the groove.
You can tighten the wire by unscrewing the handle and rotating it like a round nut until the wire is tight. Then, tighten the screw handle.
Replacement wires are available in several lengths. Measure the length of the cutting slot on your board to determine the proper length.
